Special Handrail Clamp Fittings
-
DDA1 - Elbow (Disability Access) Clamp Fitting
£4.05 £4.86 (inc. VAT) £13.33Elbow (Disability Access) DDA1 90° bend used in conjunction with two 150-3 internal connectors -
DDA2 - End Plate (Disability Access) Clamp Fitting
£5.55 £6.66 (inc. VAT) £18.40End Plate (Disability Access) DDA2 Wall bend. Screw to wall. Use in conjunction with 150-3 internal connectors. These fittings have been designed to comply with the Equality Act 2010 Part M : Access to and use of buildings Use in conjunction with BS EN1025 medium weight 32mm (1.1/4(42.4OD)) nominal bore tube. -
DDA3 - Post Connector (Disability Access) Clamp Fitting
£4.20 £5.04 (inc. VAT) £13.35DDA3 - wall bend. Screw to wall. Use in conjunction with 150-3 internal connectors. -
DDA4- Post End Connector Clamp Fitting
£4.20 £5.04 (inc. VAT) £13.35 -
DDA5 - Variable Elbow(Disability Access) Clamp Fitting
£6.00 £7.20 (inc. VAT) £19.70 -
DDA6 - Wall Plate(Disabilty Access) Clamp Fitting
£5.50 £6.60 (inc. VAT) £18.35 -
Add on 3 Way Through Clamp Fitting - 116A
£4.90 £5.88 (inc. VAT) £16.35 -
Add On 2 Socket Cross Clamp Fitting - 119A
£4.95 £5.94 (inc. VAT) £16.49 -
Acute Angle Elbow Clamp Fitting - 123
£6.10 £7.32 (inc. VAT) £16.59 -
Add On Tee Clamp Fitting - 136
From: £3.15 £3.78 (inc. VAT) £10.36The add on tee enables a structure to be extended, avoiding the need for dismantling. please contact the office before ordering this product as it could be subject to extra carriage. -
Crossover 90 degree Clamp Fitting - 137
£4.05 £4.86 (inc. VAT) £13.46 -
Add on 4 Way Cross Clamp Fitting - 158A
£7.10 £8.52 (inc. VAT) £23.54 -
Crossover Bracket Clamp Fitting - 161U
£273.00 £327.60 (inc. VAT)Pack quantity of 100 -
Eaves Fitting - Clamp Fitting - 185
£6.10 £7.32 (inc. VAT) £20.25 -
Ridge Clamp Fitting - 191
£5.05 £6.06 (inc. VAT)Designed for use in conjunction with the 185 for roofing applications on small structures. Size 4 only -
Slope Range Base Clamp Fitting - 232
From: £3.50 £4.20 (inc. VAT)An adjustable structural base fitting (4 – 10o) for a vertical post. The design of this fitting will only allow it to be installed in the correct plane. -
Horizontal Railing Base Clamp Fitting - 246
From: £4.75 £5.70 (inc. VAT) £15.85Designed for palm fixing of guardrail and balustrades to walls, parapets, steps and ramps. The upright cannot drop through the socket. FITTING ADVICE: DUE TO THE NATURE OF THESE GALVANISED CASTINGS THE MEASUREMENTS GIVEN HERE CANNOT BE PRECISE. WE THEREFORE DO NOT RECOMMEND THAT ANY BOLT HOLES ARE PRE-DRILLED PRIOR TO INSTALLATION. -
Base Flange with Kick Plate Clamp Fitting - 247
From: £8.20 £9.84 (inc. VAT) -
Slope Base Flange Clamp Fitting - 252
£6.60 £7.92 (inc. VAT)Base flange for sloping sites, adjustable between 11° - 29°. As the fixing holes in the base cannot be fixed in line with the applied load, it is only intended for light loads or structures which are sufficiently supported by virtue of their design. Where a greater load is required,type 132 is normally used, with the upright tube bent to the required angle. -
Slope Short Tee Clamp Fitting - 253
£3.90 £4.68 (inc. VAT) £12.90253 - Slope Short Tee Clamp Fitting Adjustable short tee between 11°- 29° -
Slope Long Tee Clamp Fitting - 255
£4.75 £5.70 (inc. VAT) £15.65Adjustable long tee between 11°- 29° - Size 4 only -
Slope Cross Middle Rail Clamp Fitting - 256
£4.65 £5.58 (inc. VAT) £15.40 -
Self Closing Gate 48.3mm
£87.50 £105.00 (inc. VAT) -
Medguard Standard Edge Protection
£45.00 £54.00 (inc. VAT)Our standard guardrail system is our most cost-effective edge protection system, and is suitable for the majority of buildings. Its simple design means that it is easy to install, and the rail’s flat rubber feet ensure that it will not obstruct the path of roof users, and poses little or no trip hazard. -
Medguard Inclined Edge Protection
£0.00 £0.00 (inc. VAT)Our inclined guardrail offers a streamlined option which slopes away from the edge of the roof, so it is almost undetectable from street level. It has the added bonus of keeping roof users even further away from the roof edge, making it an even safer, without sacrificing the aesthetic appeal of the building for regular users. -
Advertising Boards - Clamp Fittings
£180.00 £216.00 (inc. VAT)
Special Handrail Clamp Fittings
Special Handrail Clamp Fittings are new or special order and include the Disability Access Fittings, which are; DDA1 (Elbow), DD2 (End Plate), DDA3 (Post Connector), DDA4 (Post End Connector), DDA5 (Variable Elbow) and DDA6 (Wall Plate).
Ready-made products included in Special Handrail Clamp Fittings include: Clamp Fitting Advertising Boards, Self Closing Gate (48.3mm), Medguard Standard Edge Protection and Medguard Inclined Edge Protection.
Other Special Handrail Clamp Fittings: Add on 3 Way Through Clamp (116A), Add on 2 Socket Cross Clamp (119A), Acute Angle Elbow (123), Add on Tee (136), Crossover 90 degree (137), Add on 4 Way Cross Clamp Fitting (158A), Crossover Bracket (161U), Eaves Fitting (185), Ridge Clamp Fitting (191), Slope Range Base Fitting (232), Horizontal Railing Base Clamp (246), Base Flange with Kick Plate (247), Slope Base Flange (252), Slope Short Tee (253), Slope Long Tee (255), Slope Cross Middle Rail Clamp (256).