Contact Us on 0333 050 1186 or 01484 860920
Just £7.95 for next day delivery FREE over £75

Standard Range

Sort By
Showing products 1 to 35 of 35
101 - Short Tee Clamp Fitting

A 90° tee connection between two tubes. Typical use is on straight and level guardrail to connect the vertical to the top rail or end/mid rail to the vertical. This Q clamp fitting cannot be used to join tubes in the top of the short tee. For this the Q clamp fitting 104 Long Tee should be used. Powder coating from only £2.00 per fitting.

£1.11
£1.33 (inc. VAT)
£4.09
104 - Long Tee Clamp Fitting.

A 90° tee connection between two tubes. Typical use is on straight and level guardrail to connect the vertical to the top rail. This Q clamp fitting can be used to join tubes in the top of the twin grubscrew long tee. Powder coating from only £2.00 per fitting.

£1.75
£2.10 (inc. VAT)
£6.31
116 - Three Way Through Clamp Fitting

A 90° corner joint with the vertical passing through the Q clamp fitting. Typical use is on straight and level guardrail for connecting the mid/lower rail to the vertical at a 90° corner. Can also be used in a similar way on other rectangular structures. Powder coating from only £2.00 per fitting.

£2.02
£2.42 (inc. VAT)
£5.51
119 - Two Socket Cross Clamp Fitting

A 90° joint between a vertical and two horizontals. Typical use on straight and level guardrail to connect the mid/lower rails to the upright. The vertical must remain continuous with cross rails cut. Normally used in conjunction with the Q clamp fitting 104 Long Tee. Powder coating from only £2.00 per fitting.

£2.08
£2.50 (inc. VAT)
£5.94
125 - 90 Degree Elbow Clamp Fitting

125 90o elbow. Typical use is to connect the end vertical to the top rail in straight and level guardrail. Can also be used to create a 90o tube bend. Powder coating from only £2.00 per fitting.

£1.68
£2.02 (inc. VAT)
£4.85
128 - Three Way Elbow Clamp Fitting.

A 3 way enclosed 90° corner joint. Typical use is on straight and level guardrail at a 90 corner where an upright is in position. This Q clamp fitting can also be used to create enclosed corner joints in other square structures such as benches etc. Powder coating from only £2.00 per fitting.

£2.42
£2.90 (inc. VAT)
£6.78
131 - Wall Plate Clamp Fitting.

With four countersunk holes, this fitting is ideal as a flange to terminate handrail to a wall or other similar application. This fitting may be used on structures where it is only required as a positional fixing. Powder coating from only £2.00 per fitting. ​​​​​​​WARNING: THIS FITTING IS NOT RECOMMENDED FOR USE AS A BASE PLATE FOR GUARDRAILING

£1.72
£2.06 (inc. VAT)
£5.03
132 - Base Flange Clamp Fitting.

A structural base plate for all aspects of vertical post support. This fitting when used as a base plate for guardrailing should always be positioned with the holes across the line of the guardrail to give maximum strength. The holes in the base plate are large enough to enable the use of mechanical or chemical anchor fixings. Powder coating from only £2.00 per fitting.

£2.74
£3.29 (inc. VAT)
£9.20
133 - Plastic Plug Clamp Fitting.

A plastic stop end for use in the end of tubes. This stop end can be used in either medium or heavy gauge tube. This is only a friction fit and for a more permanent fix an adhesive is recommended. Powder coating from only £2.00 per fitting.

£0.19
£0.23 (inc. VAT)
£0.56
134 - Ground Socket Clamp Fitting.

A ground socket cast into concrete which is flush to the finished ground level. The upright is held in place using the grubscrew but can easily be removed without leaving any obstructions. Powder coating from only £2.00 per fitting.

£7.81
£9.37 (inc. VAT)
£29.00
135 - Retro Fit Tee Clamp Fitting.

An inline add-on tee used for making additions to upgrade or modify an existing structure without having the need to dismantle part or all of that structure. Powder coating from only £2.00 per fitting.

£3.01
£3.61 (inc. VAT)
£8.76
138 - Gate Eye Clamp Fitting

Female section of a two part gate hinge. Used in conjunction with Q clamp fitting reference 140.​​​​​​​ Powder coating from only £2.00 per fitting.

£1.52
£1.82 (inc. VAT)
£4.47
140 - Gate Hinge Clamp Fitting.

Male section of a two-part gate hinge used in conjunction with Qclamp fitting number 138. Powder coating from only £2.00 per fitting.

£1.70
£2.04 (inc. VAT)
£5.09
143 - Wall Mounted Handrail Bracket Clamp Fitting.

Wall mounting bracket for handrails. Can also be used to tie back structures to wall or to hold kicking plates on a guardrail. This fitting has countersunk holes and is not recommended as a structural fixing. This fitting has no ability to join tubes.​​​​​​​ Powder coating from only £2.00 per fitting.

£1.70
£2.04 (inc. VAT)
£5.18
144 - Structural Offset Side Palm Fixing Clamp Fitting.

Structural offset side palm base fixing guardrailing to walls, steps, ramps, etc. The tube is unable to pass through this fitting as supplied. Should this be required then the base must be reamed out. Access to the top fixing is restricted. It is recommended that a threaded stud is fixed first with a maximum projection of 25mm.​​​​​​​ Powder coating from only £2.00 per fitting.

£3.72
£4.46 (inc. VAT)
£11.40
145 - Non Structural Offset Palm Fixing Clamp Fitting.

This fitting is designed for palm fixing guardrailing and balustrading to walls, parapets, steps and ramps.​​​​​​​ Powder coating from only £2.00 per fitting.

£3.75
£4.50 (inc. VAT)
£11.80
146 - Structural Flush Side Palm Fixing Clamp Fitting.

Structural flush side palm base fixing guardrailing to wall, steps or ramps etc. The flush design enables posts to be tight to the structure. The tube is unable to pass through the fitting. Should this be required then the base must be reamed out. If the base is reamed out the bottom fixing will become redundant.​​​​​​​ Powder coating from only £2.00 per fitting.

£2.89
£3.47 (inc. VAT)
£9.00
147- Offset Swivel Tee Clamp Fitting

An internal swivel tee used in conjunction with other Q clamp fittings in the range to create a 360° swivel joint. Ideal use on handrail or offset guardrailing down variable angled slopes. Eliminates the requirement for specialised angle fittings. Powder coating from only £2.00 per fitting.

£3.34
£4.01 (inc. VAT)
£9.54
149 - External Straight Tube Connector Clamp Fitting.

An inline external tube connector for joining two tube a the same diameter. This fitting is not recommended to be used in a high load application. If a smooth inline joint is required we would suggest a 150 internal joint. Powder coating from only £2.00 per fitting.

£1.51
£1.81 (inc. VAT)
£4.61
150 - Internal Straight Tube Connector Clamp Fitting

An inline internal tube connector for joining two tubes of the same diameter. This fitting can only be used with 3.2mm thick walled tube. This fitting is not recommended for high tensile load applications. Powder coating from only £2.00 per fitting.

£1.57
£1.88 (inc. VAT)
£4.61
158 - Four Way Cross Clamp Fitting

A 4 way cross that enables the vertical to pass through the centre of the fitting with the four horizontal tubes joining at 90° to each other. Ideal for structures with multiple verticals. The vertical must remain either continuous with the cross rails being cut. Powder coating from only £2.00 per fitting.

£3.71
£4.45 (inc. VAT)
160 - Retro Fit Clamp On Tee Clamp Fitting

Offset add-on tee used for making additions to, upgrading or modifying an existing structure without having the need to dismantle part or all of that structure. Powder coating from only £2.00 per fitting.

£1.26
£1.51 (inc. VAT)
161 - Offset 90 deg Crossover Clamp Fitting

Designed to form a 90O crossover(offset) joint between two tubes, this fitting can reduce the need for cutting horizontal rails. Powder coating from only £2.00 per fitting.

£1.36
£1.63 (inc. VAT)
165 - Combination Socket Clamp Fitting

A common use for this fitting is for racking or similar structures, the fitting allows both upright and front and rear rails to be continuous. For any fitting advice for this item please contact us. Powder coating from only £2.00 per fitting.

£2.18
£2.62 (inc. VAT)
170 - Single Pipe Mesh Panel Clip 10 Pack Clamp Fittings

For attaching mesh panels to one side of the tube. This fitting can also be used to secure other types of material to tubes eg board. No tube can be joined using this fitting. These items are sold in packs of 10. Powder coating from only £2.00 per fitting.

£4.99
£5.99 (inc. VAT)
171 - Double Sided Mesh Panel Clip 10 pack Clamp Fittings

For attaching mesh panels to both sides of a tube. Clips are designed to suit 8mm rod. These clips are sold in a pack of 10. Powder coating from only £2.00 per fitting.

£8.50
£10.20 (inc. VAT)
176 - Three Way Outlet Tee Clamp Fitting

Mainly used in large structures with the upright passing through the fitting. The through tube cannot be joined in the fitting. Powder coating from only £2.00 per fitting.

£2.53
£3.04 (inc. VAT)
179 - Locking Collar Clamp Fitting

A simple locking collar, often used with other fittings to increase slip load capacity or to support other fittings which are left to rotate freely on tube to form hinges etc.

£1.12
£1.34 (inc. VAT)
182 - Hook Clamp Fitting

Often used where chains need to be easily removed for access. The tube cannot be joined within the fitting. Powder coating from only £2.00 per fitting.

£1.15
£1.38 (inc. VAT)
184 - Cover/Cap Clamp Fitting

Galvanized stop end for use in ends of tube. This type of stop end can be used in either medium or heavy gauge tube. This is only a friction fit for a more permanent fit an adhesive is recommended. Powder coating from only £2.00 per fitting.

£0.89
£1.07 (inc. VAT)
198 - Saddle Clamp - Clamp Fitting

Often used for mounting boards practically flush with tubes. The tube cannot be joined within the fitting. Pre-drilling is not recommended prior to receiving the product as there can be irregularities in casting that can produce small variations in the size of the holes. Any measurements shown should be regarded as a guideline only.

£2.37
£2.84 (inc. VAT)
199 - Single Pipe Clamp - Clamp Fitting

Allows for fixing to wooden planking or various panels for flush fitting. Powder coating from only £2.00 per fitting.

£1.62
£1.94 (inc. VAT)
Standard Corner Post Clamp Fitting

Available in size 3 - 4. These handrail standards enable easier and faster installation of safety railing, handrails and barriers. Comprising a 1060/1075mm length of galvanised EN10255 tube, a 132 Base Plate, a 116 Three Way Through and a 128 90o Three Way Elbow 128-4, the Standard Corner Post is available in size 3 (42.4mm) and size 4 (48.3mm). This part comes as 4 individual parts 1 x 128, 1 x 116, 1 x132 and 1 tube at 1.060 long. Contact the office for a quote - prices as low as £13.51 for a size 4. Powder coating from only £2.00 per fitting.

£15.29
£18.35 (inc. VAT)
Standard End Post Clamp Fitting

Available in size 3 - 4. These handrail standards enable easier and faster installation of safety railing, handrails and barriers. Comprising a 1060/1075mm length of galvanised EN10255 tube, a 132 Base Plate, a 101 Short Tee and a 125 90o Two Way Elbow, the Standard End Post is available in size 3 (42.4mm) and size 4 (48.3mm). Made up of : 1 x 101-3, 1 x 125-3, 1 x 132-3 and 1 x TUBE3-106 (42.4mm). Made up of : 1 x 101-4, 1 x 125-4, 1 x 132-4 and 1 x TUBE4-106 (48.3mm). Powder coating from only £2.00 per fitting.

£15.79
£18.95 (inc. VAT)
Standard Mid Rail Clamp Fitting

Available in size 3 - 4.These handrail standards enable easier and faster installation of safety railing, handrails and barriers.Comprising a 1075mm length of galvanised EN10255 tube, a 132 Base Plate, 104 Long Tee and a 119 Two Socket Cross the Standard Mid-Rail is available in size 3 (42.4mm) and size 4 (48.3mm).Powder coating from only £2.00 per fitting.

£14.61
£17.53 (inc. VAT)